mood-indigo.org - Das unabhängige Silicon Graphics User Forum
Hardware => Hardware Probleme => Thema gestartet von: Thomas W. am 24. Mai 2006, 21:32:57
-
Hallo in die Runde,
den Monitor habe ich noch immer nicht "ausgegraben", aber die ONYX2 mittels Nullmodemkabel an den PC gestöpselt:
IP27 PROM SGI Version 6.94 built 04:00:43 PM Dec 5, 2001
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30369 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/module/1/slot/n1
Testing/Initializing all memory ........... DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.94 built 03:59:15 PM Dec 5, 2001 (BE64)
2 CPUs on 1 nodes found.
Installing PROM Device drivers ............
Installing Graphics Console...
Walking SCSI Adapter 0 (/hw/module/1/slot/io1), (pci id 0)
1+ 2- 3- 4- 5- 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 2 device(s)
Walking SCSI Adapter 1 (/hw/module/1/slot/io1), (pci id 1)
1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)
Initializing PROM Device drivers .......... DONE
Cannot connect to keyboard -- check the cable.
Cannot open /dev/input/ioc3pckm0 for input
Cannot connect to keyboard -- check the cable.
Cannot open /dev/input/ioc3pckm0 for input
Checking hardware inventory ............... DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 2
No. of CPUs disabled = 0
Mem enabled = 1024 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu.
Ein "hinv" habe ich noch hinbekommen ;D
>> hinv
System SGI-IP27
2 300 MHz IP27 Processors
Main memory size: 1024 Mbytes
Graphics Controller
Integral SCSI controller 0
Integral SCSI controller 1
Integral Fast Ethernet
IOC3 serial port
Integral Fast Ethernet
IOC3 serial port
Disk drive: unit 1 on SCSI Controller 0, (dksc(0,1,0))
CDROM: unit 6 on SCSI Controller 0, (cdrom(0,6,7))
Ein "hinv -v" klappt auch:
>> hinv -v
IP27 Node Board, Module 1, Slot n1
ASIC HUB Rev 5, 100 MHz, (nasid 0)
Processor A: 300 MHz R12000 Rev 2.3
Secondary Cache 8MB 200MHz Tap 0xa , (cpu 0)
R12010FPC Rev 2.3
Processor B: 300 MHz R12000 Rev 2.3
Secondary Cache 8MB 200MHz Tap 0xa , (cpu 1)
R12010FPC Rev 2.3
Memory on board, 1024 MBytes (Standard)
Bank 0, 512 MBytes (Standard) <-- (Software Bank 0)
Bank 1, 512 MBytes (Standard)
BASEIO IO Board, Module 1, Slot io1
ASIC BRIDGE Rev 4, (widget 15)
adapter PCI-SCSI Rev 5, (pci id 0)
peripheral SCSI DISK, ID 1, SEAGATE SX150176LC
peripheral SCSI CDROM, ID 6, TOSHIBA CD-ROM XM-5401TA
adapter PCI-SCSI Rev 5, (pci id 1)
adapter IOC3 Rev 1, (pci id 2)
controller multi function SuperIO
controller Ethernet Rev 1
adapter IOC3 Rev 1, (pci id 6)
controller multi function SuperIO
controller Keyboard/Mouse
controller Parallel Port
adapter RAD , (pci id 7)
MIDPLANE, Module 1 Frequency 390 MHz
ASIC XBOW Rev 2, on midplane of Module 1
KONA Graphics Board, Module 1, Slot io4
Frage: wie kann ich rausfinden, welche Grafikauflösung eingestellt ist?
Und wie bekomme ich 1280 x 1024 @ 60 Hertz hin, damit ich mein TFT anschliessen kann?
Das TFT hatte ich angeschlosen und es gab überhaupt kein Bild :(
-
printenv
AutoLoad=Yes
dbgtty=/dev/tty/ioc30
root=dks0d1s0
nonstop=0
rbaud=19200
SystemPartition=dksc(0,1,8)
OSLoadPartition=dksc(0,1,0)
OSLoader=sash
OSLoadFilename=unix
TimeZone=PST8PDT
console=g
oldConsolePath=/hw/module/1/slot/io1
gConsoleIn=default
gConsoleOut=default
diskless=0
keybd=DE
scsihostid=00
ProbeAllScsi=n
RestorePartEnv=y
dbaud=9600
volume=80
sgilogo=y
netaddr=53.126.140.44
cpufreq=300
ConsolePath=/hw/module/1/slot/io1
NoAutoLoad=CONSOLE OPEN FAILED.
ConsoleOut=/dev/tty/ioc30
ConsoleIn=/dev/tty/ioc30
kernname=config
das console=g bedeutet doch, dass ich mit dem geeigneten Monitor eigentlich ein Bild haben müsste, oder?
Mit welchem Kommando finde ich denn heraus, welche Auflösung momentan eingestellt ist und wie ändere ich sie ggf.
-
Und wieso kann ich mein externes CD-ROM nicht auswählen, um in Ruhe mein IRIX zu installieren?
Ich habe doch keine Lust, jedesmal zur ONYX zu krabbeln und die CDs da hochkannt einzusetzen :-[
-
Hallo Thomas,
ich glaube nicht, das deine Onyx2 kaputt ist. Es kann irgendeine komische Auflösung eingestellt sein, die auf deinem Display nun nicht funzt. Bei meiner Onyx waren Splitauflösungen für mehre E-Home Projektoren eingestellt, die kein TFT kann. Logischerweise kommt dann auch kein Bild.
Die Auflösung die eingestellt ist, gibt die IR2 sofort nach dem Einschalten direkt auf dem Bildschirm an der Unterkante aus. Da stehen dann alle relevanten Werte.
Wenn der Bootmonitor geladen wird, ist die Anzeige natürlich weg.
Auf jeden Fall hab ich noch nicht gesehen, das im Maintenance Mode Grafikauflösungen angezeigt werden. Das die Grafik online ist, siehst Du an diesem Spruch im hinv: KONA Graphics Board, Module 1, Slot io4
Alles in allem sieht der hinv-v bei dir genauso aus wie meiner.
Ich würde die Kiste über die Konsole installieren, und dann bei laufendem IRIX die Startauflösung neu konfigurieren.
Gruß,
Jörg
-
Hallo Thomas,
nach Neuinstallation wird alles gut. War bei meiner onyx auch so.
Das mit dem externen lw sollte eigentlich klappen
mfg grauling
-
So, IRIX ist endlich installiert (man muss nur den richtigen Terminator auf das externe CD-ROM stecken).
Den Monitor habe ich auch ans Licht gewuchtet.
ONYX2_IR2E 1# hinv -vm
Location: /hw/module/1/slot/n1/node
MODULEID Board: barcode K000XXXX part rev
4P1G5_MPLN Board: barcode DKA323 part 013-1839-001 rev F
IP31 Board: barcode JSC565 part 030-1255-003 rev D
IP31PIMM8MB Board: barcode JSC867 part 030-1401-002 rev B
Location: /hw/module/1/slot/io4/kona
GE16-4 Board: barcode HRD909 part 030-1398-001 rev B
Location: /hw/module/1/slot/io1/baseio
MIO Board: barcode HKT352 part 030-0880-003 rev G
BASEIO Board: barcode HKT451 part 030-0734-002 rev N
2 300 MHZ IP27 Processors
CPU: MIPS R12000 Processor Chip Revision: 2.3
FPU: MIPS R12010 Floating Point Chip Revision: 2.3
CPU 0 at Module 1/Slot 1/Slice A: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
CPU 1 at Module 1/Slot 1/Slice B: 300 Mhz MIPS R12000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz Tap 0xa
Main memory size: 1408 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 8 Mbytes
Memory at Module 1/Slot 81: 1408 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 64 MB (Standard) DIMMS (enabled)
Bank 3 contains 64 MB (Standard) DIMMS (enabled)
Bank 4 contains 64 MB (Standard) DIMMS (enabled)
Bank 5 contains 64 MB (Standard) DIMMS (enabled)
Bank 6 contains 64 MB (Standard) DIMMS (enabled)
Bank 7 contains 64 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
Disk drive: unit 1 on SCSI controller 0 (unit 1)
CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
CDROM: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3 parallel port: plp1
Graphics board: InfiniteReality2E
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
Iris Audio Processor: version RAD revision 7.0, number 1
Origin BASEIO board, module 1 slot 1: Revision 4
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n1: Revision 6.136
IO6prom on Global Master Baseio in Module 1/Slot io1: Revision 6.136
Bild ist auch da:
ONYX2_IR2E 2# /usr/gfx/gfxinfo
Graphics board 0 is "KONAL" graphics.
Managed (":0.0") 1280x1024
Display has 2 channels
4 GEs (of 4), occmask = 0x0f
4MB external BEF ram, 32bit path
1 RM9 board (of 1) 1/0/0/0
Texture Memory: 64MB/-/-/-
Medium pixel depth
32K cmap
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 72.00Hz (1280x1024_72.vfo)
Schnurrt wie ein Kätzchen, die Kleine ;D
-
Schnurrt wie ein Kätzchen, die Kleine ;D
aber wahrscheinlich ein wenig lauter ;D
Günter