mood-indigo.org - Das unabhängige Silicon Graphics User Forum
Hardware => Hardware Probleme => Thema gestartet von: ravemaster2000 am 29. November 2007, 08:46:12
-
So habe ne schöne Fuel bei Ebay ersteigert. Alles bestens dachte ich. Auspacken Einschalten Geht. Geht ebend nicht. Die Lightbar blinkt die ganze Zeit weiss vor sich hin und es kommt kein Bild.
Das eine Fuel länger zum Booten braucht weiss ich aber keine 10 min. Über die L1 Console auf dem Mainboard habe ich schonmal reingeschaut. Lüfterdrehzahl etc. werde aber aus den Werten nicht richtig schlau. Am seriellen Anschluss Terminal mit Nullmodemkabel dran. Aber auch da kommen nur ein paar xxxxCCCCCxxxxx xxxxCCC. Bin am Ende meiner Kunst da es meine erste Fuel ist. Ich wäre echt dankbar für ein bisschen Hilfe.
Danke schonmal der Rave
-
Oliver,
ich sagte du sollst den Ouput von dem abgefragten Environment hier posten damit die Leute vergleichen koennen bzw. sagen koenen was bei dir fehlt.
Bezueglich der Hyroglyphen an der Console.... kann es sein das hier andere Terminalsettings gefragt sind als am L1 Controller?
Gruss
Joerg
-
Jepp Jörg hat mal wieder recht. Hier die Daten der seriellen Console
IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004
Running in DDR mode
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30360 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming globa
Global master is /hw/rack/001/bay/01
Intializing any CPUless nodes.............. DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64)
1 CPUs on 1 nodes found.
Automatic update of PROM environment disabled
PS/2 Keyboard & Mouse diagnostics
Found mouse on port 0
Found keyboard on port 1
PS/2 Keyboard & Mouse diagnostics passed
Graphics diagnostics
Odyssey board #0 found on nasid 0
Running Odyssey xtalk sanity diag...
Board version 1 - Buzz revision 2B
On board sdram size: 32 Mb
Cas latency: CAS 3
4 banks by sdram module
Running Odyssey Buzz registers diag...
Device passed diagnostics
Installing PROM Device drivers ............
Base I/O Ethernet set to /dev/ethernet/ef0
Installing Graphics Console...
graphics install: searching for pipe 0
Walking SCSI Adapter 0, (pci id 1)
1+ Device Vendor Product: SGI IC35L036UWDY10-0
2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)
Walking SCSI Adapter 1, (pci id 1)
1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)
Initializing PROM Device drivers .......... DONE
A 000: *** General Exception on node 0
A 000: *** EPC: 0xc00000001fc47e58 (0xc00000001fc47e58)
A 000: *** Press ENTER to continue.
-
Wo ist die Ausgabe vom Environment monitoring?
Gruss
Joerg
-
env
ERROR: command not found.
001a01-L1>env
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.12
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.12
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.10
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.46
1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.47
5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.10
3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.29
PIMM0 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
Fuel SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.52
Fuel CPU Enabled 10% 1.44/ 1.76 20% 1.28/ 1.92 1.61
PIMM0 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.49
PIMM0 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.29
PIMM0 5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.10
XIO 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
XIO 5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.07
XIO 2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.46
XIO 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.29
Description State Warning RPM Current RPM
-------------- ---------- ----------- -----------
FAN 0 EXHAUST Enabled 920 1152
FAN 1 HD Enabled 1560 2290
FAN 2 PCI Enabled 1120 1618
FAN 3 XIO 1 Enabled 1600 2229
FAN 4 XIO 2 Enabled 1600 2052
FAN 5 PS Enabled 1600 1968
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
-------------- ---------- --------- --------- --------- ---------
NODE 0 Enabled 60C/140F 65C/149F 70C/158F 24C/ 75F
NODE 1 Enabled 60C/140F 65C/149F 70C/158F 23C/ 73F
NODE 2 Enabled 60C/140F 65C/149F 70C/158F 20C/ 68F
PIMM Enabled 60C/140F 65C/149F 70C/158F 26C/ 78F
ODYSSEY Enabled 60C/140F 65C/149F 70C/158F 19C/ 66F
BEDROCK Enabled 70C/158F 75C/167F 80C/176F 24C/ 75F
001a01-L1>env
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.12
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.12
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.10
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.34
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.46
1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.47
5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.10
3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.29
PIMM0 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
Fuel SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.52
Fuel CPU Enabled 10% 1.44/ 1.76 20% 1.28/ 1.92 1.61
PIMM0 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.49
PIMM0 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.27
PIMM0 5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.10
XIO 12V bias Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
XIO 5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.07
XIO 2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.46
XIO 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.29
Description State Warning RPM Current RPM
-------------- ---------- ----------- -----------
FAN 0 EXHAUST Enabled 920 1152
FAN 1 HD Enabled 1560 2305
FAN 2 PCI Enabled 1120 1618
FAN 3 XIO 1 Enabled 1600 2229
FAN 4 XIO 2 Enabled 1600 2052
FAN 5 PS Enabled 1600 1980
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
-------------- ---------- --------- --------- --------- ---------
NODE 0 Enabled 60C/140F 65C/149F 70C/158F 25C/ 77F
NODE 1 Enabled 60C/140F 65C/149F 70C/158F 24C/ 75F
NODE 2 Enabled 60C/140F 65C/149F 70C/158F 20C/ 68F
PIMM Enabled 60C/140F 65C/149F 70C/158F 30C/ 86F
ODYSSEY Enabled 60C/140F 65C/149F 70C/158F 19C/ 66F
BEDROCK Enabled 70C/158F 75C/167F 80C/176F 26C/ 78F
-
Boot halt mal von CD. Bezueglich "0xc00000001fc47e58" gibts nen Verweis nach nekochan.net. Die CPU ist doch nun da, wo hast du denn gestern gesehen das die Fehlt?
Gruss
Joerg
-
So habe glaube alle versucht. Nach diesem:
A 000: *** General Exception on node 0
A 000: *** EPC: 0xc00000001fc47e58 (0xc00000001fc47e58)
A 000: *** Press ENTER to continue.
gehts nicght weiter. Kein Bild und keine möglichkeit von Cd IRIX zu installieren.Benutze einen DVI-I adapter der normalerweise dem Mac Mini beiligt. Aber der sollte ja genormt sein. Keine Ahnung. An Jörg -> glaube ich komme mal am Wochenende bei Dir vorbei.
-
So habe mal ohne Keyboard und Mouse gebootet. Lief alles wunder bar. Mit gibt es den oben genannten Fehler. Dann setenv console d und mit Keyboard und mouse gebootet. Alles wunderbar. Miniroot wurde übertragen und dann das. Ich schätze hier ist die Grafikkarte breit da der error auf Node 0 Nasid weisst und das die V10 ist (oder?) Hier der Auszug von der Console:
IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004
Running in DDR mode
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30361 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/rack/001/bay/01
\\\\Intializing any CPUless nodes.............. \\DONE
\Checking partitioning information ......... DONE
No other nodes present; becoming partition master
\Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64)
1 CPUs on 1 nodes found.
Automatic update of PROM environment disabled
PS/2 Keyboard & Mouse diagnostics
Found keyboard on port 1
No mouse found, skipping mouse test
Missing PS/2 device(s) BUT console set to "d"
PS/2 Keyboard & Mouse diagnostics passed
Graphics diagnostics
Odyssey board #0 found on nasid 0
Running Odyssey xtalk sanity diag...
Board version 1 - Buzz revision 2B
On board sdram size: 32 Mb
Cas latency: CAS 3
4 banks by sdram module
Running Odyssey Buzz registers diag...
Device passed diagnostics
Installing PROM Device drivers ............
Base I/O Ethernet set to /dev/ethernet/ef0
Walking SCSI Adapter 0, (pci id 1)
1+ Device Vendor Product: SGI IC35L036UWDY10-0
2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)
Walking SCSI Adapter 1, (pci id 1)
1- 2- 3- 4- 5+ Device Vendor Product: YAMAHA CDR200t
6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)
Initializing PROM Device drivers .......... DONE
Checking hardware inventory ............... DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 1
No. of CPUs disabled = 0
Mem enabled = 1024 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
Starting up the system...
To perform system maintenance instead, press <Esc>
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 2
Installing System Software...
Press <Esc> to return to the menu.
1) Remote Directory 2)[Local CD-ROM]
*a) Local SCSI CD-ROM drive 5, on controller 1
Enter 1-2 to select source type, a to select the source, <esc> to quit,
or <enter> to start:
Insert the installation CD-ROM, then press <enter>:
It appears that a miniroot install failed. Either the system is
misconfigured or a previous installation failed.
If you think the miniroot is still valid, you may continue booting
using the current miniroot image. If you are unsure about the
current state of the miniroot, you can reload a new miniroot image.
You may abort the installation and return to the menu, or you can
fix (reset to normal) the miniroot install state
See the 'Software Installation Guide' chapter on Troubleshooting for
more information
Enter 'c' to continue booting the old miniroot with no state fixup.
Enter 'f' to fix miniroot install state, and try again
Enter 'r' to reload the miniroot.
Enter 'a' to abort (cancel) the installation.
Enter your selection and press ENTER (c, f, r, or a) r
Copying installation program to disk.
......... 10% ......... 20% ......... 30% ......... 40% ......... 50%
......... 60% ......... 70% ......... 80% ......... 90% ......... 100%
Copy complete
IRIX Release 6.5 IP35 Version 07141608 System V - 64 Bit
Copyright 1987-2003 Silicon Graphics, Inc.
All Rights Reserved.
QLFC: running as interrupt thread.
QLFC: using spinlocks.
WARNING: Xbow at /hw encountered Fatal error
xtalk PIO Read error in kernel mode
widgetnum: 0xd
srccpu: 0x0
srcnode: 0x0
errnode: 0x0
sysioaddr: 0xd233c08
xtalkaddr: 0x233c08
vaddr: 0x920000000d233c08
epc: 0xc00000000045aedc
ef: 0xa800000000b93af8
(NOTE: CPU 0=/hw/module/001c01/node/cpubus/0/a)
kl_ioerror_handler Failed handling PIO Read error in kernel mode
widgetnum: 0xd
srccpu: 0x0
srcnode: 0x0
errnode: 0x0
sysioaddr: 0xd233c08
xtalkaddr: 0x233c08
vaddr: 0x920000000d233c08
epc: 0xc00000000045aedc
ef: 0xa800000000b93af8
(NOTE: CPU 0=/hw/module/001c01/node/cpubus/0/a)
HARDWARE ERROR STATE:
+ Errors on node Nasid 0x0 (0)
+ IP35 in /hw/module/001c01/node [serial number MSX727]
+ BEDROCK signalled following errors.
+ BEDROCK PI 0 Error Interrupt Register: 0x200000
+ 21: CPU A received uncorrectable error during uncached load
+ BEDROCK PI 0 Error Status 0 A Register: 0x800348cf03600006
+ 02<->00: rrb error type 6 Response Data Error
+ 24<->17: message command 0xb0 Reply(PRPLY)
+ 61<->25: error address 0x1a46781 << 3 = (0xd233c08)
+ 63<->62: error status valid (no over_run)
+ BEDROCK PI 0 Error Status 1 A Register: 0x10480000400000
+ 28<->21: crb timeout counter 0x2
+ 52<->43: crb status 0x209
End Hardware Error State
++FRU ANALYSIS BEGIN
No rules triggered: Insufficient data
Timeout Histogram is empty.
++FRU ANALYSIS END
PANIC: Kernel Data Bus error in IO space at physical address 0xd233c08 (EPC 0xc00000000045aedc)
Restarting the machine...
-
Mit was fuer einer IRIX version hast du eigentlich gebootet?
Gruss
Joerg
ps: Man darf ruhig mehr als 2min eingeloggt bleiben in einem IRC Server
-
6.5.21