Hallo in die Runde,
den Monitor habe ich noch immer nicht "ausgegraben", aber die ONYX2 mittels Nullmodemkabel an den PC gestöpselt:
IP27 PROM SGI Version 6.94 built 04:00:43 PM Dec 5, 2001
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30369 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/module/1/slot/n1
Testing/Initializing all memory ........... DONE
Checking partitioning information ......... DONE
No other nodes present; becoming partition master
Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.94 built 03:59:15 PM Dec 5, 2001 (BE64)
2 CPUs on 1 nodes found.
Installing PROM Device drivers ............
Installing Graphics Console...
Walking SCSI Adapter 0 (/hw/module/1/slot/io1), (pci id 0)
1+ 2- 3- 4- 5- 6+ 7- 8- 9- 10- 11- 12- 13- 14- 15- = 2 device(s)
Walking SCSI Adapter 1 (/hw/module/1/slot/io1), (pci id 1)
1- 2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 0 device(s)
Initializing PROM Device drivers .......... DONE
Cannot connect to keyboard -- check the cable.
Cannot open /dev/input/ioc3pckm0 for input
Cannot connect to keyboard -- check the cable.
Cannot open /dev/input/ioc3pckm0 for input
Checking hardware inventory ............... DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 2
No. of CPUs disabled = 0
Mem enabled = 1024 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 5
Command Monitor. Type "exit" to return to the menu. Ein "
hinv" habe ich noch hinbekommen
>> hinv
System SGI-IP27
2 300 MHz IP27 Processors
Main memory size: 1024 Mbytes
Graphics Controller
Integral SCSI controller 0
Integral SCSI controller 1
Integral Fast Ethernet
IOC3 serial port
Integral Fast Ethernet
IOC3 serial port
Disk drive: unit 1 on SCSI Controller 0, (dksc(0,1,0))
CDROM: unit 6 on SCSI Controller 0, (cdrom(0,6,7)) Ein "
hinv -v" klappt auch:
>> hinv -v
IP27 Node Board, Module 1, Slot n1
ASIC HUB Rev 5, 100 MHz, (nasid 0)
Processor A: 300 MHz R12000 Rev 2.3
Secondary Cache 8MB 200MHz Tap 0xa , (cpu 0)
R12010FPC Rev 2.3
Processor B: 300 MHz R12000 Rev 2.3
Secondary Cache 8MB 200MHz Tap 0xa , (cpu 1)
R12010FPC Rev 2.3
Memory on board, 1024 MBytes (Standard)
Bank 0, 512 MBytes (Standard) <-- (Software Bank 0)
Bank 1, 512 MBytes (Standard)
BASEIO IO Board, Module 1, Slot io1
ASIC BRIDGE Rev 4, (widget 15)
adapter PCI-SCSI Rev 5, (pci id 0)
peripheral SCSI DISK, ID 1, SEAGATE SX150176LC
peripheral SCSI CDROM, ID 6, TOSHIBA CD-ROM XM-5401TA
adapter PCI-SCSI Rev 5, (pci id 1)
adapter IOC3 Rev 1, (pci id 2)
controller multi function SuperIO
controller Ethernet Rev 1
adapter IOC3 Rev 1, (pci id 6)
controller multi function SuperIO
controller Keyboard/Mouse
controller Parallel Port
adapter RAD , (pci id 7)
MIDPLANE, Module 1 Frequency 390 MHz
ASIC XBOW Rev 2, on midplane of Module 1
KONA Graphics Board, Module 1, Slot io4Frage: wie kann ich rausfinden, welche Grafikauflösung eingestellt ist?
Und wie bekomme ich 1280 x 1024 @ 60 Hertz hin, damit ich mein TFT anschliessen kann?
Das TFT hatte ich angeschlosen und es gab überhaupt kein Bild