So habe mal ohne Keyboard und Mouse gebootet. Lief alles wunder bar. Mit gibt es den oben genannten Fehler. Dann setenv console d und mit Keyboard und mouse gebootet. Alles wunderbar. Miniroot wurde übertragen und dann das. Ich schätze hier ist die Grafikkarte breit da der error auf Node 0 Nasid weisst und das die V10 ist (oder?) Hier der Auszug von der Console:
IP35 PROM SGI Version 6.210 built 02:33:51 PM Aug 26, 2004
Running in DDR mode
Testing/Initializing memory ............... DONE
Copying PROM code to memory ............... DONE
Discovering local IO ...................... DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 30361 usec
Waiting for peers to complete discovery.... DONE
No other nodes present; becoming global master
Global master is /hw/rack/001/bay/01
\\\\Intializing any CPUless nodes.............. \\DONE
\Checking partitioning information ......... DONE
No other nodes present; becoming partition master
\Loading BASEIO prom ....................... DONE
BASEIO PROM Monitor SGI Version 6.210 built 02:30:38 PM Aug 26, 2004 (BE64)
1 CPUs on 1 nodes found.
Automatic update of PROM environment disabled
PS/2 Keyboard & Mouse diagnostics
Found keyboard on port 1
No mouse found, skipping mouse test
Missing PS/2 device(s) BUT console set to "d"
PS/2 Keyboard & Mouse diagnostics passed
Graphics diagnostics
Odyssey board #0 found on nasid 0
Running Odyssey xtalk sanity diag...
Board version 1 - Buzz revision 2B
On board sdram size: 32 Mb
Cas latency: CAS 3
4 banks by sdram module
Running Odyssey Buzz registers diag...
Device passed diagnostics
Installing PROM Device drivers ............
Base I/O Ethernet set to /dev/ethernet/ef0
Walking SCSI Adapter 0, (pci id 1)
1+ Device Vendor Product: SGI IC35L036UWDY10-0
2- 3- 4- 5- 6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)
Walking SCSI Adapter 1, (pci id 1)
1- 2- 3- 4- 5+ Device Vendor Product: YAMAHA CDR200t
6- 7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)
Initializing PROM Device drivers .......... DONE
Checking hardware inventory ............... DONE
**** System Configuration and Diagnostics Summary ****
CONFIG:
No. of NODEs enabled = 1
No. of NODEs disabled = 0
No. of CPUs enabled = 1
No. of CPUs disabled = 0
Mem enabled = 1024 MB
Mem disabled = 0 MB
No. of RTRs enabled = 0
No. of RTRs disabled = 0
DIAG RESULTS:
ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****
Starting up the system...
To perform system maintenance instead, press <Esc>
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 2
Installing System Software...
Press <Esc> to return to the menu.
1) Remote Directory 2)[Local CD-ROM]
*a) Local SCSI CD-ROM drive 5, on controller 1
Enter 1-2 to select source type, a to select the source, <esc> to quit,
or <enter> to start:
Insert the installation CD-ROM, then press <enter>:
It appears that a miniroot install failed. Either the system is
misconfigured or a previous installation failed.
If you think the miniroot is still valid, you may continue booting
using the current miniroot image. If you are unsure about the
current state of the miniroot, you can reload a new miniroot image.
You may abort the installation and return to the menu, or you can
fix (reset to normal) the miniroot install state
See the 'Software Installation Guide' chapter on Troubleshooting for
more information
Enter 'c' to continue booting the old miniroot with no state fixup.
Enter 'f' to fix miniroot install state, and try again
Enter 'r' to reload the miniroot.
Enter 'a' to abort (cancel) the installation.
Enter your selection and press ENTER (c, f, r, or a) r
Copying installation program to disk.
......... 10% ......... 20% ......... 30% ......... 40% ......... 50%
......... 60% ......... 70% ......... 80% ......... 90% ......... 100%
Copy complete
IRIX Release 6.5 IP35 Version 07141608 System V - 64 Bit
Copyright 1987-2003 Silicon Graphics, Inc.
All Rights Reserved.
QLFC: running as interrupt thread.
QLFC: using spinlocks.
WARNING: Xbow at /hw encountered Fatal error
xtalk PIO Read error in kernel mode
widgetnum: 0xd
srccpu: 0x0
srcnode: 0x0
errnode: 0x0
sysioaddr: 0xd233c08
xtalkaddr: 0x233c08
vaddr: 0x920000000d233c08
epc: 0xc00000000045aedc
ef: 0xa800000000b93af8
(NOTE: CPU 0=/hw/module/001c01/node/cpubus/0/a)
kl_ioerror_handler Failed handling PIO Read error in kernel mode
widgetnum: 0xd
srccpu: 0x0
srcnode: 0x0
errnode: 0x0
sysioaddr: 0xd233c08
xtalkaddr: 0x233c08
vaddr: 0x920000000d233c08
epc: 0xc00000000045aedc
ef: 0xa800000000b93af8
(NOTE: CPU 0=/hw/module/001c01/node/cpubus/0/a)
HARDWARE ERROR STATE:
+ Errors on node Nasid 0x0 (0)
+ IP35 in /hw/module/001c01/node [serial number MSX727]
+ BEDROCK signalled following errors.
+ BEDROCK PI 0 Error Interrupt Register: 0x200000
+ 21: CPU A received uncorrectable error during uncached load
+ BEDROCK PI 0 Error Status 0 A Register: 0x800348cf03600006
+ 02<->00: rrb error type 6 Response Data Error
+ 24<->17: message command 0xb0 Reply(PRPLY)
+ 61<->25: error address 0x1a46781 << 3 = (0xd233c08)
+ 63<->62: error status valid (no over_run)
+ BEDROCK PI 0 Error Status 1 A Register: 0x10480000400000
+ 28<->21: crb timeout counter 0x2
+ 52<->43: crb status 0x209
End Hardware Error State
++FRU ANALYSIS BEGIN
No rules triggered: Insufficient data
Timeout Histogram is empty.
++FRU ANALYSIS END
PANIC: Kernel Data Bus error in IO space at physical address 0xd233c08 (EPC 0xc00000000045aedc)
Restarting the machine...
