Irix > Installation/Update
"Autoboot failed" nach IRIX Netzwerkinstallation
Ebbi:
Moin,
nachdem ich nun die Nase voll von BSD und Linux habe, habe ich die Octane als Installationsserver für die Indy genommen. Das hat auch prima geklappt, allerdings klappt das Booten nicht mehr. Nach der Installation kommt "Requickstarting ELF files" und dann werde ich zum Reboot aufgefordert. Die Indy bootet aber nicht, sondern beglückt mich mit folgender Ausgabe:
--- Zitat ---Unable to execute scsi(0)disk(1)rdisk(0)partition(0)/unix: media not loaded
Autoboot failed.
scsi(0)disk(1)rdisk(0)partition(0)/unix: media not loaded.
Hit Enter to continue.
--- Ende Zitat ---
Nachdem ich die Suche im Forum und Google bemüht und die tollsten Ratschläge gelesen hatte, habe ich beschlossen einfach noch einmal ganz von vorne anzufangen.
Also fx.ARCS über Netz gebootet, die Platte als root-Disk neu partitioniert und die Installation nochmal laufen lassen.
Leider kein Erfolg, das selbe Ergebnis.
Als ich damals von CD installiert hatte, gab es das Problem nicht.
Nun hoffe ich auf hilfreiche Tipps von den echten IRIX Gurus hier. :)
jobeh:
Trag hab in die bootinfo den bootfile mit ein.
--- Code: ---fx/label/show> boot
----- bootinfo-----
root partition = 0 swap partition = 1 bootfile = /unix
--- Ende Code ---
Gibt auch ne PROM Variable fuer... aber weis nicht obs bei den alten Kisten auch geht.
Gruss
Joerg
Ebbi:
Einen solchen Beitrag hatte ich auch gefunden und das überprüft.
Genau so steht das aber die bootinfo bei mir drin. ???
PROM Parameter habe ich folgende, die werden wohl automatisch eingetragen:
--- Zitat ---SystemPartition=scsi(0)disk(1)rdisk(0)partition(8 ) (<-- Leerzeichen, da sonst Smiley)
OSLoadPartition=scsi(0)disk(1)rdisk(0)partition(0)
OSLoadFilename=/unix
OSLoader=sash
--- Ende Zitat ---
jobeh:
Dann zeig mal die Partionsdaten alle an und ueberpruefe ob der Kernel denn da auch liegt.
Gruss
Joerg
Ebbi:
Das Label:
--- Code: ---fx/label/show> a
----- current drive parameters-----
Error correction enabled Enable data transfer on error
Don't report recovered errors Do delay for error recovery
Don't transfer bad blocks Error retry attempts 1
Do auto bad block reallocation (read)
Do auto bad block reallocation (write)
Drive readahead enabled Drive buffered writes enabled
Drive disable prefetch 65535 Drive minimum prefetch 0
Drive maximum prefetch 65535 Drive prefetch ceiling 65535
Number of cache segments 7
Read buffer ratio 0/256 Write buffer ratio 0/256
Command Tag Queueing disabled
----- current drive geometry-----
Tracks/zone = 5215 Sect/track = 320
Alt sect/zone = 0 Interleave = 1 Cylinders = 11474
Alt track/volume = 0 Cylinder skew = 20 Heads = 5
Alt track/zone = 0 Track skew = 11 Data bytes/sec = 512
Rotational rate = 7200
----- partitions-----
part type blocks Megabytes (base+size)
0: xfs 528384 + 17387856 258 + 8490
1: raw 4096 + 524288 2 + 256
8: volhdr 0 + 4096 0 + 2
10: volume 0 + 17916240 0 + 8748
----- bootinfo-----
root partition = 0 swap partition = 1 bootfile = /unix
----- directory entries-----
0: sgilabel block 2 size 512 2: sash block 621 size 316416
1: ide block 3 size 316416
----- sgi-info-----
serial = name = IBM DNES-309170 SA30
----- please choose one (? for help, .. to quit this menu)-----
[para]meters [part]itions [b]ootinfo [a]ll
[g]eometry [s]giinfo [d]irectory
--- Ende Code ---
--- Zitat von: jobeh am 08. Februar 2007, 17:33:17 ---...und ueberpruefe ob der Kernel denn da auch liegt.
--- Ende Zitat ---
Äh, wie denn?
Single User über Netzwerk booten kann ich nicht.
Navigation
[0] Themen-Index
[#] Nächste Seite
Zur normalen Ansicht wechseln