Hardware > Hardware Probleme

ONYX2: KAPUTT??? kommt kein Bild...

<< < (2/2)

Thomas W.:
So, IRIX ist endlich installiert (man muss nur den richtigen Terminator auf das externe CD-ROM stecken).

Den Monitor habe ich auch ans Licht gewuchtet.


--- Code: ---ONYX2_IR2E 1# hinv -vm
Location: /hw/module/1/slot/n1/node
        MODULEID Board: barcode K000XXXX   part              rev   
      4P1G5_MPLN Board: barcode DKA323     part 013-1839-001 rev  F
            IP31 Board: barcode JSC565     part 030-1255-003 rev  D
     IP31PIMM8MB Board: barcode JSC867     part 030-1401-002 rev  B
Location: /hw/module/1/slot/io4/kona
          GE16-4 Board: barcode HRD909     part 030-1398-001 rev  B
Location: /hw/module/1/slot/io1/baseio
             MIO Board: barcode HKT352     part 030-0880-003 rev  G
          BASEIO Board: barcode HKT451     part 030-0734-002 rev  N
2 300 MHZ IP27 Processors
CPU: MIPS R12000 Processor Chip Revision: 2.3
FPU: MIPS R12010 Floating Point Chip Revision: 2.3
CPU 0 at Module 1/Slot 1/Slice A: 300 Mhz MIPS R12000 Processor Chip (enabled)
  Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz  Tap 0xa
CPU 1 at Module 1/Slot 1/Slice B: 300 Mhz MIPS R12000 Processor Chip (enabled)
  Processor revision: 2.3. Scache: Size 8 MB Speed 200 Mhz  Tap 0xa
Main memory size: 1408 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 8 Mbytes
Memory at Module 1/Slot 81: 1408 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
  Bank 2 contains 64 MB (Standard) DIMMS (enabled)
  Bank 3 contains 64 MB (Standard) DIMMS (enabled)
  Bank 4 contains 64 MB (Standard) DIMMS (enabled)
  Bank 5 contains 64 MB (Standard) DIMMS (enabled)
  Bank 6 contains 64 MB (Standard) DIMMS (enabled)
  Bank 7 contains 64 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
  CDROM: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3 parallel port: plp1
Graphics board: InfiniteReality2E
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
Iris Audio Processor: version RAD revision 7.0, number 1
Origin BASEIO board, module 1 slot 1: Revision 4
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 6
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 7
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n1: Revision 6.136
IO6prom on Global Master Baseio in Module 1/Slot io1: Revision 6.136

--- Ende Code ---

Bild ist auch da:


--- Code: ---ONYX2_IR2E 2# /usr/gfx/gfxinfo
Graphics board 0 is "KONAL" graphics.
        Managed (":0.0") 1280x1024
        Display has 2 channels
        4 GEs (of 4), occmask = 0x0f
        4MB external BEF ram, 32bit path
        1 RM9 board (of 1) 1/0/0/0
        Texture Memory: 64MB/-/-/-
        Medium pixel depth
        32K cmap
        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 72.00Hz (1280x1024_72.vfo)

--- Ende Code ---
Schnurrt wie ein Kätzchen, die Kleine  ;D

guefz:

--- Zitat von: Thomas W. am 08. September 2006, 21:16:09 ---Schnurrt wie ein Kätzchen, die Kleine  ;D

--- Ende Zitat ---

aber wahrscheinlich ein wenig lauter  ;D

Günter

Navigation

[0] Themen-Index

[*] Vorherige Sete